|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
U2203B RGB Video Amplifier System for Monitors Description The U2203B-A is a wideband video amplifier IC system especially designed for use in high-resolution RGB monitors. The IC includes three well matched video amplifiers, three gated differential amplifiers for blacklevel clamping and brightness control and the function for simultaneously contrast control. Separate adjustment of the maximum gain of each channel is also possible. Features D 3 channels, high bandwidth (90 MHz @ -3 dB) D Matched attenuators for contrast control D Black-level clamping for brightness control Vs1 1 SUPPLY REG. 1k D Independent gain control of each amplifier D ESD protection according to MIL-STD. 883 28 Vs1 CONTRAST CAP 2 27 R DRIVE CONTRAST CAP 3 RED 40 90 26 R CLAMP (-) R VIDEO IN 4 25 R VIDEO OUT R CLAMP CAP 5 24 R CLAMP (+) G VIDEO IN 6 GREEN 1k 40 23 Vs2 GROUND 7 90 22 G DRIVE G CLAMP CAP 8 9 21 G CLAMP (- ) B VIDEO IN B CLAMP CAP BLUE 1k 40 2.4V REF CONTRAST CONTROL 90 20 G VIDEO OUT 10 19 G CLAMP (+) Vin REF CONTRAST 11 12 18 B DRIVE 17 B CLAMP (-) Vs1 13 1.4V REF U2203B 95 10749 16 B VIDEO OUT CLAMP GATE 14 15 B CLAMP (+) Figure 1. Block diagram TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 1 (7) U2203B Pin Description VS1 Ccontr Ccontr Vin, R Cclamp, R Vin, G GND Cclamp, G Vin, B Cclamp, B VBias Vcontr VS1 VGate 1 2 3 4 5 6 7 8 9 10 11 12 13 14 96 12388 28 VS1 27 RR 26 VR- 25 Vout, R 24 VR+ 23 VS2 22 RG 21 VG- 20 Vout, G 19 18 17 16 15 VG+ RB VB- Vout, B VB+ Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Symbol VS1 Ccontr Ccontr Vin, R Cclamp, R Vin, G GND Cclamp, G Vin, G Cclamp, B VBias Vcontr VS1 VGate VB+ Vin, B VB- RB VG+ Vout, G VG- RG VS2 VR+ Vout, R VR- RR VS1 Function Supply voltage Contrast cap. Contrast cap. Video input (R) Clamp cap. (R) Video input (G) Ground Clamp cap. (G) Video input (B) Clamp cap. (B) Bias voltage (RGB-inputs) Contrast control Supply voltage Inverted clamp gate Clamp amplifier (B+) Video output (B) Clamp amplifier (B-) Drive resistor (B) Clamp amplifier (G+) Video output (G) Clamp amplifier (G-) Drive resistor (G) Supply voltage (outputs) Clamp amplifier (R+) Video output (R) Clamp amplifier (R-) Drive resistor (R) Supply voltage Figure 2. Pinning Absolute Maximum Ratings Parameters Supply voltage Pins 1, 13, 28 and 23 Input voltage at all other pins Video output current Pins 16, 20 and 25 Junction temperature Storage temperature range Symbol VS Vin IV Tj Tstg Value 13.5 0 toVS 28 125 -40 to 125 Unit V V mA C C Operating Range Parameters Ambient temperature range Supply voltage range Pins 1, 13, 23 and 28 Symbol Tamb VS2, VS1 Value 0 to 80 11.0 to 13.0 Unit C V 2 (7) TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 U2203B Thermal Resistance Parameters Junction ambient (DIP28) Symbol RthJA Value 46 Unit K/W Electrical Characteristics Test conditions unless otherwise specified, reference point Pin 7, Tamb = 25C, VS1 = VS2 = 12 V, V12 = 6 V (contrast); V14 = 0 V (inv. gating); V15 = V19 = V24 = 2 V (brightness) Parameters DC-values Supply current Input bias voltage Input bias current Switching voltage gating "on" Switching voltage gating "off" Switching current gating "on" Switching current gating "off" Charge current clamping capacitor Discharge current clamping capacitor Video outputs, VO Low level High level Output offset between two p amplifiers Test Conditions / Pins VS1 only, Pins 1, 13 and 28 Pin 11 Pins 4, 6 and 9 Pin 14 Pin 14 V14 = 0.8 V Pin 14 V14 = 2.0 V Pin 14 V5,8,10 = 0 V Pins 5, 8 and 10 V5,8,10 = 5 V Pins 5, 8 and 10 Pins 16, 20 and 25 V5,8,10 = 0 V V5,8,10 = VS V15, V19, V24 = 2 V V15, V19, V24 = 4 V Video gain Maximum video gain Middle video gain Dynamic gain range Video gain match (any 2 outputs) Video bandwidth unpeaked (C = 0 pF) optimal peaking (C = 27 pF) Video cross talk 1) ICL+ ICL- 0.8 -1.2 1.0 -1.0 1.2 -0.8 IG "H" 5 8 Symbol IS1 VinREF IinREF VG "L" VG "H" IG "L" -1 2.3 1 0.8 Min. Typ. 60 Max. 70 2.5 10 Unit mA 5 1.3 1.5 -0.01 mA V V V 2.0 mA mA mA mA VO"L" VO"H" (2 V) DVO DVO 8.0 0.8 8.6 1.0 50 50 V V mV mV (4 V) V15 = V19 = V24 = 4 V (brightness); fIN = 1 MHz V12 = 12 V GVmax 16.0 V12 = 5 V GVmid GVD V12 = 12 V GVMmax GVMmid V12 = 5 V 1) GVM-30 V12 = 2.2 V V12 = 12 V (f-3dB) V12 = 12 V (f-3dB) fIN = 10 kHz fIN = 10 MHz BWV BWVP CT10kHz CT10MHz -50 17.7 8.5 50 0.1 0.1 0.3 65 90 dB dB dB dB dB dB MHz MHz dB dB -47 Measured 30 dB below maximum gain TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 3 (7) U2203B VS (+12V) 100 mF 1 100 nF 2 100 nF 5 mF 3 4 75 W G Video in 75 W 10 kW 5 mF 8 100 nF 9 75 W 5 mF 10 kW 10 100 nF 11 12 10 kW Black level gate I/P 13 100 nF 14 15 10 kW 10 kW 100 nF 93 7632 28 27 51 W 100 W C 26 25 24 23 22 390 W R Clamp (-) To cascade driver (R) R Video in 5 mF 10 kW 100 nF 5 6 7 100 nF 51 W 100 W U2203B 21 20 C G Clamp (-) To cascade driver (G) B Video in 390 W 19 18 C 17 16 390 W 91 W G Clamp (-) To cascade driver (B) Contrast control 0 ... 12 V Black level (brightness) control 10 kW 10 nF Figure 3. Typical application circuit 4 (7) TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 U2203B AC Characteristics 20 18 16 14 Gain ( dB ) 12 10 8 6 4 2 0 1 95 10748 C = 0 pF C = 10 pF C = 27 pF C = 47 pF 10 Frequency ( MHz ) 100 1000 Figure 4. Gain vs. frequency (various peaking), V12 = 12 V (contrast), V15 = V19 = V24 = 4 V (brightness) 10 0 Relative gain ( dB ) -10 -20 -30 -40 -50 -60 1 95 10747 10 Frequency ( MHz ) 100 1000 Figure 5. Relative gain vs. frequency (no peaking), V12 = variable (contrast), V15 = V19 = V24 = 4 V (brightness), 0 dBrel = 17.7 dB, C = 0 pF TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 5 (7) U2203B 10 0 Releative gain ( dB ) -10 -20 -30 -40 -50 -60 1 95 10746 10 Frequency ( MHz ) 100 1000 Figure 6. Rel. gain vs. frequency (optimized peaking), V12 = variable (contrast), V15 = V19 = V24 = 4 V (brightness), 0 dBrel = 17.7 dB, C = 27 pF Package Information Package DIP28 Dimensions in mm 37.40 36.90 15.29 15.19 4.0 3.8 0.8 0.5 3.3 0.58 0.48 0.35 0.25 13.9 13.7 1.54 33.02 28 2.54 16.1 15.3 15 technical drawings according to DIN specifications 13023 1 14 6 (7) TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 U2203B Ozone Depleting Substances Policy Statement It is the policy of TEMIC TELEFUNKEN microelectronic GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances ( ODSs). The Montreal Protocol ( 1987) and its London Amendments ( 1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. TEMIC TELEFUNKEN microelectronic GmbH semiconductor division has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2 . Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency ( EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C ( transitional substances ) respectively. TEMIC can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use TEMIC products for any unintended or unauthorized application, the buyer shall indemnify TEMIC against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. TEMIC TELEFUNKEN microelectronic GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 ( 0 ) 7131 67 2831, Fax number: 49 ( 0 ) 7131 67 2423 TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 7 (7) |
Price & Availability of U2203B |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |